17za.com
工業軟管泵系列產品是吸收了國外先進技術而開發的一種新型的、多功能、多用途工業軟管泵。我廠研發的高性能軟管泵徹底擺脫了傳統泵葉輪和軸密封的運行模式，對粘度大、腐蝕性大、流體雜質大的介質輸送具有極大的優勢，和傳統蠕動泵輸送泵有著截然不同的原理，應用范圍廣泛。
Industrial hose pump series is a new type, multifunctional and multi-purpose industrial hose pump developed by absorbing foreign advanced technology. The high-performance hose pump developed by our factory has completely rid of the traditional pump impeller and shaft seal operation mode, and has great advantages for medium transportation with high viscosity, corrosiveness and large fluid impurities. Different principles have a wide range of applications.
對于軟管泵的內部結構，通常有擠壓輪和滑靴兩種設計方法。對于軟管擠壓，擠壓輪的設計更為柔軟，因為當軟管被壓縮時，擠壓輪在軟管表面滾動?；サ脑O計不僅壓縮了軟管，而且在軟管表面產生滑動摩擦，使擠壓后的管道產生很大的磨損。因此，在采用滑靴結構設計時，必須在泵殼內壁添加足夠的潤滑油，以幫助延長軟管的使用壽命?；サ脑O計和在泵中添加潤滑劑，在一定程度上增加了滑靴蠕動泵的復雜性和成本。
工業軟管泵不銹鋼齒輪泵，可輸送非潤滑油飲料低腐蝕性液體，配銅齒輪可輸送汽油苯等低內點液體。由于齒輪泵自吸能力差，一般是由于齒輪泵泵腔間隙較大所致。同時也是如果齒輪泵輸出端沒有“止回閥”，則必須是下一級齒輪泵的止回閥或控制閥。移動固定后，周圍工作人員可恢復手術。
Industrial hose pump stainless steel gear pump, can transport non-lubricant beverages with low corrosive liquids, with copper gears can transport gasoline, benzene and other low internal point liquids. Due to the poor self-priming ability of the gear pump, it is generally caused by the large gap between the pump cavity of the gear pump. At the same time, if there is no "check valve" at the output of the gear pump, it must be a check valve or control valve of the next gear pump. After moving and fixing, the surrounding staff can resume surgery.
多用途移動泵站的主要用途：
多用途移動泵站基于泵設計開發，大流量軟管泵是市政給排水中常用的一種泵型，擁有大量的潛在用戶，其產品主要用于污水、初沉污泥、濃縮污泥等的抽排輸送。由于轉子泵具備自吸能力強、耐干轉、流量范圍大、耐磨損的特點受到國內設計單位和使用單位的青睞。
The main purpose of the multi-purpose mobile pumping station:
The multi-purpose mobile pumping station is based on the design and development of a pump. The large-flow hose pump is a type of pump commonly used in municipal water supply and drainage. It has a large number of potential users. Extraction delivery. Rotor pumps are favored by domestic design units and users due to their strong self-priming ability, resistance to dry running, large flow range and wear resistance.
采購 混凝土拋丸機_認準豫信致誠機械設備(南陽市分公司)_廠家直銷_直接讓利20%，錯過此次機會在等一年。
1、軟管的更換與調整
（1）更換軟管時，先將兩端管卡螺栓松掉，并將管卡拆下，再將其中一端的吊圈螺栓松掉，將一端短管從膠管中抽出，點動電機將膠管自泵內推出；然后將新的軟管從拆下短管的一端插入泵殼與壓輥之間，點動電機，將軟管裝入；再將吊圈固定、管卡裝上，至此更換任務完成。尤其注意再安裝軟管時，務必將軟管與泵殼貼緊，確認后方能投入正常運行。
（2）軟管使用200小時左右，可將軟管轉動90度，對單管軟管泵除轉動方向外，還可前后抽動軟管，以改變軟管的壓點，延長軟管的使用壽命。
